Category Archives: Uncategorized

Slackware 14 USB HDD Install

OK yall, a quick rundown on how I setup a usb HDD with a bootable Slackware 14 install today.

Firstly, I installed the base system from the CD, with my partition table looking a little something like this..

/dev/sda1   *     63                 1558304         779121           83  Linux                     /boot
/dev/sda2         1558305        9365894        3903795          82  Linux swap           swap
/dev/sda3   *     9365895       204684164     97659135       83  Linux                     /
/dev/sda4          204684165   1953519615   874417725+   7  HPFS/NTFS/exFAT   /store

Now during the install I chose the simple LILO install option, into the MBR of /dev/sda.

After that I modified my initrd tree, firstly by deleting it, located at /boot/initrd-tree, and then by running mkinitrd, which will give us a fresh tree and populate it. Now to get a working initrd image to bring up the usb disk on boot, first I had to modify /boot/initrd-tree/wait-for-root and set the value to something in seconds to allow the drive time to come up once the modules are loaded. I set mine to 15. Next I modified the fstab to only reference UUIDs when mounting the disks, as If you are using this on different machines, you may find the disk moves locations depending on how many disks are in said machine, ie : /dev/sda if singlular, or first drive (unlikely, given USB) becomes /dev/sdb or c, if detected after others. This way the drive is always referenced correctly and you dont get kernel panics. You can get the UUID of your partitions by ‘blkid’.

My fstab as follows

UUID=af7efa55-2f37-415a-b131-130d2accbd5d        swap             swap       defaults         0   0
UUID=ddee4a6a-900d-494e-9573-acb6fd371faf        /                    ext4         defaults         1   1
UUID=dac53074-92d8-4fb1-abc9-0bd0f0631102       /boot             ext2        defaults         1   2
UUID=3E58608D586045AD        /store        ntfs        fmask=111,dmask=000 1   0
#/dev/cdrom      /mnt/cdrom      auto        noauto,owner,ro,comment=x-gvfs-show 0   0
/dev/fd0             /mnt/floppy       auto        noauto,owner         0   0
devpts               /dev/pts            devpts     gid=5,mode=620   0   0
proc                  /proc                 proc        defaults                   0   0
tmpfs                /dev/shm          tmpfs       defaults                   0   0

Next I built my initrd image using the command ‘mkinitrd -s /boot/initrd-tree -k 3.2.29-smp -m ehci-hcd:uhci-hcd:usb-storage -f ext4  -o /boot/initrd.gz’. You will note the modules we are placing into the image, these will be loaded and allow the drive to be initialised, and the root fs duties to be handed off to it. Change the variables for kernel and filesystem as needed.

Lastly, I configured and reinstalled LILO. Again, like the example above, we want to modify it to only use UUIDs as reference, and to add in the lines for our initrd. Make sure you place the initrd line above the root line when configuring, it denotes hierachy.

My lilo.conf entries, dont forget to change the boot line to the target HDD.

boot = /dev/sdc
image = /boot/vmlinuz
initrd = /boot/initrd.gz
root = “UUID=ddee4a6a-900d-494e-9573-acb6fd371faf”
label = Slack14

Lastly, run ‘lilo -v’ to commit the whole thing to the MBR.